This guide will brief you about Supernet DSLW200 (Type-4). It will guide you about how to physically connect modem as well as firmware configuration of this modem pictorially. It is a easy and step-by-step guide for you.
You have chosen Supernet DSLW200 (Type-4). It is a type-4 modem in context to BSNL modem terminology.
Brief Specifications : –
- It has four Fast Ethernet ports (10/ 100 Mbps) for PC connectivity.
- It provides a down-link speed up to 24 Mbit/s and an up-link speed up to 1 Mbit/s.
- The device supports WLAN access, as WLAN AP or WLAN router, to internet. It is compliant with IEEE 802.11b/g/n specifications (Speed upto 150 Mbps) and complies with WEP, WPA and WPA2 security specifications.
- Supports network security including NAT
Front Panel:
Rear Panel:
I will discuss the PPPoE configuration (i.e Always-On mode) for this modem pictorially with required text when needed. I will break the whole modem configuration procedure in four sections.
Basic Physical Connection:
Section I:
LAN Configuration:
Put the IP address in Local Area Connection as-
IP Add: 192.168.1.11 (Say)
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1
Section II:
Step 1: Open Internet Explorer or other browser, and put 192.168.1.1 in address bar of browser and hit enter. One window of modem configuration will open, put the user name and password as-
User Name: admin
Password: admin
After providing user name and password, you will come to the home page of modem.
Same modem buy on last month…. a cross signal comes at internet access at some time..internet goes disconnect…then comes back …Why this happening any drivers needed for this modem??
NO drivers needed
your DSL line may be fault ,
check the line
SNR :: more than 20
attenuation :: as much as low possible
I have supernet router purchased from Bsnl please tell how to block pornsites on this router…
click on —- access management
click on — filter
Filter Type Selection — URL Filter
active–yes
index : 1
url full address of pornsites
save
index : 2
url full address of pornsites
save
total you can enter 16 0r 17 sites
choose –management tab
click– sysrestart
System Restart with : Current Settings
click — RESTART
wait for a minute , to restart a router ,
now see entered pornsites are not accessble
Porn sites can’t be blocked by router, to block porn sites install Antivirous and throgh block these sites.
Protected Object
This object on the RomPager server is protected
show above error on login .Hard reset is also not work .
Please guide.
press and hold the *Reset* switch for 30 to 45
seconds, and again wait for 2mins and change the *LAN* port of the
modem (*Example:
while reset if the LAN cable connected to LAN1 after reset connect LAN
cable to LAN2,3 or 4)*
Hi can u please help me how to reset.. And im unable to connect to wifi
exactly same problem sirji.
Please upgrade your modem firmware it is available in bsnl site
connect the ,modem to another computer , and try to access
when i type 192.168.1.1 on my web browser, than i can’t logged into my modem settings.. why????
Same problem with me.
admin admin not working. although my internet is working.
press and hold the *Reset* switch for 30 to 45
seconds, and again wait for 2mins and change the *LAN* port of the
modem (*Example:
while reset if the LAN cable connected to LAN1 after reset connect LAN
cable to LAN2,3 or 4)*(u need to re configure the modem if reset)
use microsoft IE.
Try with a different browser or Check if you have a static IP.
this happened due to corrupted on INTERNET EXPLORER on windows .
use firefox or chrome browser to access .
if your modem has already configured to wifi means
use smart phone browser to configure that’s it
Several Computer browsers have that problem. try it in firefox. otherwise u have make brower compactible ppte type encryption or allow subnet mask
hello sir
I am using Supernet SW2201502-140484 WIFI MODEM on BSNL line.
There is a problem that when i connected my mobiles and laptop it automatically open porn sites or redirect me to porn sites.
kindly suggest me the steps to stop it in wifi configration
its not a cellular or modem issue. please clear you history, default & cookies with your explorer.
This is due to malware infection. Reset your browser and use malwarebytes antimalware. Reset your phone to factory default. Also clean your memory card.
its bcoz ur browser has been infected by malware. u should download a malware cleaner and scan it.
1) check your laptops has virus or phishing websites or malwares are changed the browser webpage .
2) use Kaspersky total security for best performance ,I am using from year 2010 onwards ,still no problem.
3) use Kaspersky internet security for android too, install and update and do full scan , if applications are found malicious , just uninstall them , uninstall all third party applications.
4) clear the browser caches and cookies in computer and in smartphone.
5) download ADWCLEANER application from google search ,run in computer , in tools –options –check al boxes
and mode is normal, databases as server , click reset and ok.and click SCAN,waiting for 1o minutes to download databases for server and it scan itself,if found malicious and some other problems ,just CLEAN IT ,wait for 30 minutes to reboot ,
that’s it
when i type 192.168.1.1 in browser i can’t log into router. please help. I haven’t change username and password of router
I can’t connect the internet, indicate internet light on in “Red” why ?
because lan settings are corrupted or DSL is good or the bsnl server is not working
username: admin
password: admin
NOT WORKING.
Can anybody please help.
Although I am able to access Internet over Wifi.
Not able to connect via LAN
What may be the problem
press and hold the *Reset* switch for 30 to 45
seconds, and again wait for 2mins and change the *LAN* port of the
modem (*Example:
while reset if the LAN cable connected to LAN1 after reset connect LAN
cable to LAN2,3 or 4)*(u need to re configure the modem if reset)
After resetting can I configure modem through WiFi? Or I have to connect modem first with LAN cable? Bcz after resetting my modem’s WiFi I’d is not showing up..
Plz help..
can i use this bsnl dslw200 modem as a wifi repeater/bridge ??
if yes kindly enlighten me with the same
no
you an connect many wifi mobile ,but wps is not there ,
I mean ,wifi hotspot not available
how to forward port in DSLW200-SY modem?????????? i cant forward 80 port . help meeee???????
I am facing problem in changing password of Wi Fi
My modem is ADSL2+CPEs Type W2
DSLW200
How can I get driver of the same
The modem has been supplied by local BSNL Anisabad Patna Exchange.
Can’t you send the required driver be email as an attachment
this modem does need any drivers , if your modem has been connected usb means , then driver is must .
you can access the modem from smartphones
by different passwords
password , admin ,PASSWORD , USER123 , user123 , 12345678 ,87654321 .
Sir my modem reset not working this time
these modems are giving problem.after some time of uasage they are not opening.hard resetting is only solution
NOT WORKING IN ROUTER USER NAME AND PASSWORD
USER NAME :ADMIN
PASSWORD: ADMIN
NOT WORKING
PLS HELP ME
There is a small hole next to LAN ports. With power ON press a small pin into hole and hold for few seconds. Release and you should be able to use Admin for username and password.
press and hold the *Reset* switch for 30 to 45
seconds, and again wait for 2mins and change the *LAN* port of the
modem (*Example:
while reset if the LAN cable connected to LAN1 after reset connect LAN
cable to LAN2,3 or 4)*(u need to re configure the modem if reset)
Reset Modem and Assign Manual 192.168.1. Series IP Address to Your System it’s Working.
hey need to type: admin in small not in caps
bsnl supernet modem giving up ip adress(192.168.1.1) after switch on off .problem is resolved only by hard resetting the modem . this problem is again and again facing by us .we already done the manuall setting but problem is not being resolved .this problem is facing in all supernet modem .plz give us some advise so that we can resolve the problem
pls gv ur mail id. i
pls gv ur mail id to
sanjuraj123@gmail.com
DID you getting dns server unavailable with default gateway as 182.168.1.1.
please clearly,explain whats the exact problems,if possible take screenshot and add in cloud storage ,give links
when put username and password as admin it isn’t login in.plz reply
Reset your modem
How to control bandwidth in dslw200 router?
Here my modem wlan is on for 10sec and light will off
its power adapter problem
or do reset the modem
User Name: admin
Password: admin
not working since recently
use other passwords:::
password
user123
ADMIN
PASSWORD
12345678
hi , can anybody say how to configure bsnl static Ip address configuration
static ip address has be subscribed per user by paying rs 2000 ,ask your telephone exchange or bsnl modem office.
How to upgrade uploading speed? Router model DSLW200 and downloading speed is 6mbps approx. but uploading speed is 0.64mpbs. Please fix this or upload any new firmware for DSLW200 if available.
uploading speed is depends upon the
1) DSL telephone
2) modem compatible
3) uploading server ( yahoo server , Microsoft server ) like this .
4) check your computer has viruses, Trojans or malicious programs are blocking
5) check the antivirus software it may be blocked the ip addresses or the servers to avoid uploadings
same problem with me also,
username:admin
password:admin
not able to log in.
please help if anyone have solution for it.
Or manual reset is only solution for this problem.
NOT WORKING IN ROUTER USER NAME AND PASSWORD
USER NAME :ADMIN
PASSWORD: ADMIN
NOT WORKING
PLS HELP ME
Protected Object
This object on the RomPager server is protected
show above error on login .Hard reset is also not work .
Please guide.
Model Number:DSLW200-SY
Connection Type:Bridge
unable to access wifi data
use connection as PPPOA/PPPOE
and make sure wifi as enabled and wifi SSID is allowed for broadcast
if password protected means , enter password in smartphone
How to reduce WiFi range??
Please help
normally wifi gets access up to in circle of radius 10 meters only without any walls or obstacles
Admin admin not working pshelp
How to setup mac filtaring?
which type of mac filtering you want to do ,
for declining wifi access to all mobiles or particular mobile
how to forward port in DSLW200-SY modem?????????? i cant forward
1. 192.168.1.1 clik enter
2.advanced setup
3.clik nat option and setup internet ip
4.clik DMZ
5.eanable DMZ and enter u r internet ip and save go back
6. enter Virtual Server and setup u r protocol
how can i allow my antivirus to get update from internet. please give me some setting instructions.
all antivirus updates automatically , you don’t do anything on modem.
choose the update mode as automatically in antivirus application
can i use this bsnl dslw200 modem as a wifi repeater?
Harsh Verma
“Protected Object
This object on the RomPager server is protected”
show above error on login .Hard reset is also not work .
Please help me out.
i can not acces this modem throw the username nd password : admin
admin
clik modem back side reset button
use other passwords:::
password
user123
ADMIN
PASSWORD
12345678
use other passwords:::
password
user123
ADMIN
PASSWORD
12345678
username:admin
password:admin
not able to log in.
please help if anyone have solution for it.
Or manual reset is only solution for this problem.
nd repl me fast
can uh give me new firmware my router DSLW200
Is there any way to restrict the speed of the devices connected to the modem or at least the speed of wifi
Dear Madam/Sir
After Firmware update i followed the configuration setting as per your method but still its not connecting.
Could you please give some more details of the configuration.
Any suggestions???
Thank you
With regards
Santosh
Thank u nice information!
how can i check connected wifi devices in this router
i can not acces this modem throw the username nd password : admin
admin
is porn sites are blocked on this modem
tell me
I am not able to configure and goto my modem homepage . I want to do an ip blacklist. I have a static ip and am connected to internet. I dont know how to do this .. Will Resetting delete my modem settings ??? Please tell me
I reset my router.now i want to know the procedures for bringing it back in action